• AUTOPOL IV Suppliers


The AUTOPOL IV is a microprocessor based automatic polarimeter that is available in one, two and six wavelength versions. The AUTOPOL IV’s features include: readout in Specific Rotation, Optical Rotation, and concentration, customer defined and labeled programs for push button readout, large LCD display and touchscreen user interface, temperature display and correction, push button wavelength selection, statistics, 3 USB ports, RS 232 and parallel printer ports.

Product Description

Measurement Modes

The AUTOPOL IV Laboratory Polarimeter can readout directly in one of four measurement modes: Optical Rotation, Specific Rotation, Concentration or Specific Rotation Plus. Specific Rotation Plus allows a correction to be applied to a result for loss on drying. Each measurement mode can be activated via touchscreen selection. Sample tubes can be specified at any length (e.g. 50mm, l00mm, 200mm), or entered as a precise dimension (e.g., 199.98mm). Concentration is entered as a percentage.

Temperature Control of Samples in a Laboratory Polarimeter

Temperature control of samples is allowed through rubber gasketting in the Autopol door, which permits tubing to be connected from an external temperature controlled Water Bath to the jacket of a jacketed polarimeter sample tube.

Laboratory Polarimeter Cells up to 200mm Long

Instruments of some manufacturers accept only special sample cells, with maximum lengths of 100mm. Autopols accept standard sample cells up to 200mm long. A 200mm sample cell offers twice the sensitivity as the same solution in a 100mm cell. This is especially useful for solutions having small rotations. Also some pharmacopeia monographs require a 200mm (2dm) cell like the USP monograph for Methotrexate. Rudolph Research Laboratory Polarimeter sample cells are made to NIST standards; and the complete range of sizes and types are listed in Technical Bulletin 913. NIST certificates are available for cell length validation.

 Sample Specific Programs

These programs allow for parameters such as tube length, concentration, specific rotation, wavelength, sample measurement range, measurement scale and temperature correction to be pre-specified.

The programs can be labeled with an alphanumeric name (e.g. Dextrose 2). The operator simply selects the sample program from the alphabetic list and the AUTOPOL’s is ready to make measurements. Sample specific programs can be set to read either Optical Rotation, specific rotation, concentration or user defined scales. A user defined scale is a linear equation based on the measured value and input parameters.

Multiple Wavelengths

The AUTOPOL IV Automatic Polarimeter comes in single, dual and six wavelength models. Wavelength selection is completely automatic and is accomplished via menu selection. There are no lamps or filters to manually remove or insert. The following wavelengths are available: 365nm, 405nm, 436nm, 546nm, 589nm and 633nm. Optional wavelengths include: 578nm, 880nm and various other wavelengths are available; contact the factory for more information.

White-light Source Permits Spectral Versatility

The tungsten-halogen lamp employed in AUTOPOL Polarimeters is a compact, reliable,  low-cost, high intensity light source that allows any desired wavelength in the visible spectrum to be selected by means of a narrow band multilayer interference filter. The AUTOPOL standard 10nm bandwidth is specified to permit high energy throughput and sensitivity for sample transmittances of only 0.01 % (O. D. = 4), while minimizing the effects of sample ORD and color.

Temperature Display and Correction

The AUTOPOL IV Automatic Polarimeter comes standard with a temperature probe which can be inserted into the Polarimeter cell as shown to the left. The temperature of either the sample compartment or the solution itself can be continuously displayed.

Print Format

Numerous parameters, such as sample name, tube length, concentration, wavelength, time and date, temperature correction and statistics can be printed after each polarimeter measurement or after a group of measurements. This is accomplished by designating the required parameters, via menu entry, during the print format setup mode.

USB, RS 232, and Printer Communication

The AUTOPOL IV Polarimeter offers three USB ports, two RS 232 serial ports, and an Ethernet port for connecting to your network. The RS 232 port allows data to be sent to a computer when the print key is pressed, when the computer requests the data or at predefined time intervals. Measurements can be remotely controlled from a host computer and the printout format and parameters can be selected via menu entry. Utilizing a USB port, all plug-and-play Windows compatible printers may be added.

Real-Time Clock

AUTOPOL IV contains a real-time clock that tracks time and date. All measurements can be date and time stamped when printed out. The time is continually displayed in the upper right hand corner of the display.


AUTOPOL IV calculates the mean, the standard deviation and records the minimum and maximum readings for up to 999 measurements Measured data for statistical calculation can be printed in either one of two ways: automatically, at predetermined time intervals or manually, by pressing the print key. Statistics for a batch of samples can be accomplished by pressing the page feed key. Statistics on time varying optically active samples can be compiled by measuring a sample at a predetermined rate and for a predetermined number of measurements.

Range Limits

Sample range limits can be specified in sample specific programs, (e.g. 24.8° Arc – 25.7° Arc). When a range is specified and the measurement falls outside this specification the display will read “out of range”. Two TTL level signals are available for out of range conditions. These signals are useful for process control or alarms.


No matter which Autopol automatic polarimeter you choose, Rudolph uses the same high quality optics. While other manufacturers use Polaroid Plastic Dichroic Sheet Polarizers, Rudolph does not. Instead, Rudolph uses the same high quality Glan Thompson Calcite Polarizers in all its models.

Why are high quality polarizing prisms important? Because prisms are two of the most critical optical components in the polarimeter. Polaroid polarizers are made of a polymeric plastic where the molecules are stretches and oriented in a specific direction so as to linearly polarize light. These types of plastic sheet polarizers are very inexpensive ($50.00 USD) and are vulnerable to heat, warp over time, deterioriate from moisture, and also have greater light absorption than Calcite Polarizers. In many cases, the plastic polarizers must be replaced in 3 – 5 years. Glan Thompson Calcite Polarizers are comprised of a carbon crystalline structure similar to diamond and have excellent light transmission characteristics. The quality of these prisms is so good, Rudolph guarantees its prisms over the life of the polarimeter.

Polarimeter Calibration and Validation

Rudolph understands that today’s cGLP/cGMP laboratories must validate measurement and temperature. Therefore Rudolph offers 6 different NIST Traceable Quartz Calibration Standards that can be matched to your application. The Autopol IV also comes with a Temperature Validation Cell so that your temperature measurement can be traced to NIST. See Technical Bulletin 913 for more information.

Autopol IV – Specifications

AUTOPOL IV Specifications
Measuring Mode Optical Rotation
Specific Rotation
Specific Rotation Plus Concentration
User Defined Scale
Sugar Degrees
Measuring Scale Degrees Arc Optical Rotation
Resolution 0.001° Arc Optical Rotation 0.001% Concentration 0.001 Specific Rotation
Accuracy 0.002° up to 1°, 0.2% up to 5°, 0.01° above 5°
AP Accuracy Option Autopol IV Single ±0.002° Arc Optical Rotation
Autopol IV Dual ±0.002° Arc Optical Rotation
Autopol IV Six Wavelength Accuracy (546nm and 589nm): ±0.002° Arc Optical Rotation
AP Resolution Option Selectable Resolution: 0.01, 0.001, 0.0001° Arc
Reproducibility 0.002° Arc Optical Rotation
Measuring Range ± 89° Arc Optical Rotation,
± 999.99 Specific Rotation,
0-99.9% Concentration
Prism Glan Thompson Calcite
Optical Wavelengths 365nm, 405nm, 436nm, 546nm, 589nm, 633nm
Wavelength Selection Touchscreen Selectable: 1, 2 and 6
21 CFR Part 11 Compliant Software Yes with optional PC software
Temperature Control By external water bath (Standard)
TempTrol™ Automatic Electronic Heating & Cooling 15° – 40°C
±0.2° (Optional)
TempTrol™ Accuracy ±0.2°C (optional)
Temp. Probe Range 10°-100°C
Temp. Probe Accuracy ±0.1°C
Measurement Time 4°/sec slewing rate &
5 sec nominal settling time
Light Source Tungsten-Halogen 6V, 20W, Avg. 2,000 hr. life
Sample Chamber Accepts sample tubes up to 200mm
Data Storage 8 GB Non-removable Compact Flash
Communication Interface 3 – USB Ports, 2 – RS232 Ports, Ethernet Port for Network Connection
Calibration Automatic calibration via touchscreen
Operating System Windows 7 Embedded
Display 8 inch Color, 800 x 600 pixel resolution with 400 nits of brightness.
User Interface Touchscreen
Automatic Sensitivity Control Measures samples with transmittance as low as 0.01% (up to O.D. 4.0)
Input Power 100 – 240V, 50/60Hz
Operating Dimensions 30″W x 11.5″H x 17″D,
762mm W x 431.8mm H x 279.4mm D
Shipping Dimensions 42″W x 24″H x 21″D,
1066.8mm W x 609.6mm H x 533.4mm D
Operating Weight 85 lbs (39 kg)
Shipping Weight 115 lbs (52.1 kg)
Temperature Compensation Temperature of the sample can be corrected to a reference temperature
Calendar/Clock Battery-backed clock. Time and date sent to computer and printer


There are no reviews yet.

Only logged in customers who have purchased this product may leave a review.